A washer that will not drain or bangs through every spin is a laundry-day emergency. We service top-load and agitator washers across Las Vegas and the surrounding valley, backed by 28 years of appliance repair experience. From a clogged water inlet valve and a failed drain pump to a worn tub bearing and a lid switch that will not lock, we find the actual component failure and get your washer filling, washing, and draining again.
Southern Nevada water is very hard. Every fill leaves calcium and magnesium mineral scale in the water inlet valve screens, the dispenser drawer, and the tub. Over time that scale restricts fill flow, clogs the dispenser, and traps detergent residue that causes sour odors. Descaling regularly helps, but a washer already filling slowly or smelling has a component the scale has worn down.
These are the washing machine issues Las Vegas households call us about most often.
No water entering the tub, or a trickle that drags the cycle out.
Water left in the tub after the cycle ends, or clothes coming out soaked.
Noise during the spin cycle from a worn bearing, tub, or suspension.
Motor humming but the agitator or drum not moving through the cycle.
Lid switch or door lock fault stopping the cycle from starting.
Water escaping during fill or spin from a hose, valve, or tub seal.
Control board throwing an error or the unit not powering on at all.
A washer works by balancing the fill, the drive, the drain, and the lid lock. When one of those fails, the symptom can look like several different problems. We identify the real part so the repair lasts.
Washer experience across top-load, agitator, and high-capacity brands. Each name links to our full brands page.
Safety note: Always unplug the washer and shut the water supply valves before checking anything inside or behind it. If you smell gas near the unit, leave the home and call Southwest Gas or 911.
We look at the washer's age, the failed component, and how the repair compares to the replacement cost. Hard water scale may have aged a unit faster here than the same model in a softer-water region.
A washer with a single failed pump, valve, belt, or lid switch usually makes sense to repair.
An older washer with a tub bearing failure or a control board fault may cost more to repair than replacing the unit.
Four steps from first call to a washer that fills, washes, and drains.
Reach us by phone or submit the form with your washer make and symptom.
We test the fill valve, drain pump, drive, lid switch, and control board.
We explain the failed part and you decide how to proceed.
We complete the repair and confirm the cycle fills, washes, and drains.
A sour smell usually means detergent and softener residue are trapped in the tub, the dispenser, or the drain pump area. Hard Las Vegas water leaves mineral scale that traps that residue. Running a hot cleaning cycle helps, but a persistent smell can point to a low drain or a buildup a component part has worn down. A technician can confirm the real cause.
Soaking-wet clothes mean the spin cycle is not extracting water. The most common causes are a failed drain pump motor, a clogged drain pump, a worn drive belt, or a bad spin-speed control. A kinked drain hose can also stop it from draining fully. A technician can test each part and confirm the cause.
It depends on the washer's age, the failed component, and how the repair compares to replacing the unit. A washer with a single failed pump, valve, belt, or lid switch often makes sense to repair. An older unit with a tub bearing or control board failure may be ready to replace.
A loud bang on spin usually points to a worn tub bearing, a failing suspension, or an unbalanced load the machine cannot redistribute. If the noise happens with a balanced load, a bearing or suspension part is likely worn. A technician can inspect the tub and suspension and confirm.
Southern Nevada water is very hard. As it fills the tub, calcium and magnesium leave mineral scale in the water inlet valve screens, the dispenser, and the drum. Over time that scale restricts fill flow, clogs the dispenser, and strains the valve. Descaling regularly helps slow the buildup.
A washer that fills but will not agitate usually has a broken drive coupling, a worn belt, or a failed motor control. The lid switch or door lock can also stop the cycle before the agitator engages. A technician can test the drive and control to confirm which part failed.
We come to your home. Serving Las Vegas and the surrounding valley.
Tell us what your washer is doing. Submit your request below or call our team directly.
